Jono's KLZE Project - Turbo Build Begins
-
Finally showing my support for the forum :)
:twisted: I like these stickers alot! :twisted:
If you look carefully at the top of the pic you can see the sticker on the other side too :p
-
me to same place as well
-
that's nice! it would look funny if I had one on my car, driving around the USA and all 8)
-
@01e54732d0=Mooneggs:
that's nice! it would look funny if I had one on my car, driving around the USA and all 8)
want one? lol.
can someone send me a sticker! ill send the payment, and if mooneggs wants one send me too, and ill get it for him.
-
Hello.. Been some time since iv'e updated this!
Well the car is currently in bits in my garage as I am finally installing the Clutch nearly 4 years after the swap :D
After getting the gearbox out it would seem that the rear crankshaft oil seal has gone :( so the car has to stay in bits until I can get my hands on a new seal.
Ive also got a set of mx-6 stainless steel exhaust headers/downpipe which will be fitted once the gearbox is back in, the only issue I can see with these is the length, I may need to modify the mid section :shock:
Jon
-
yep thats the one that gets us all easyest way is to take out the cat and make a small pipe to go in place
-
Well its been a while again… ( Over two years I think !!! )
Just had the thing MOT'd (which it passed!) and now its off the road for some serious and lengthy project work.
A little update on where things are;
Just over two years ago I got the new cluch installed, made a huge difference, no more slipping clutch which is great. Installed the new headers and built a full exhaust system using a MX-6 cat.
Then the alternator failed, so installed a refurbished one... this failed 6 months later, got that exchanged... 5 months later that one went too, so I just forked out the money for a brand new one, over a year later and its still running fine.
I bought a new daily driver earlier this year (A Nisan Qashqai for those that are interested) so now the MX-3 sits in the garage.
After thinking long and hard about it I have decided to do a full overhaul of the entire car, probably to make it a track car, this includes the turbo install which has been very very very long overdue.
I don't have any particular time scales for this, its going to just be something I do when I get time but I'm really looking forward to getting stuck into the project again much to my missus disappointment lol.
Will need some advice though on the latest mods that are out there as I have lost touch a little over the last few years, I'm particularly intersted in suspension & big brake upgrades as a starter.
Will be looking to do a full engine rebuild too, I'm thinking DE valve springs as a must with forged internals.
Even thinking a custom roll cage and custom interior.
Will keep you posted.
Jono
-
Glad your still progressing with things.
Where abouts you located in Essex. Pm me if you don't want to post location. I'm in kent and not too far.
-
Hey Garfy, I'm near Romford. Question about your roll cage, did you build that or get a company to do it? I have just requested a quote for one from fabricage.
So looks like I will be ordering a basic turbo kit from the US this weekend… exciting times ahead :D
Jono
-
It was made by company called fast road conversions. It's worth about 1-1.5k all in!. But luckily for me it didn't cost me a penny as I wired up there new workshops and swallowed the labour cost.
Ah Romford isn't too far. And you have tdi close by when it comes to mapping and aftermarket ecu
Have a word with marco as he maybe able to create you a shopping list from uk suppliers for turbo parts. May work out cheaper after shipping & customs
-
So 8 years after my ZE swap the engine is back out of the car as I actually start the turbo build!
Managed to get it out much faster than the first time and I had no assistance this time! :D Although I did take a nice breaker bar to the knee thanks to a rusted bolt! :shock:
The bay looks a little empty right now but plenty of work to do here. I made a small mistake when releasing the power steering belt tensioner, I forgot to loosen the retaining nut and broke the metal work so looks like I need a new tensioner - if anyone has one please let me know.
I've started to tear down the engine earlier then expected as I need to know the bore size for the custom Wiseco pistons I want to order.
Unfortunately it looks like my cam's have seen better days, so that's more money I need to spend.
Also looks like I might have some water in there, hopefully thats not caused by anything too serious!
Will keep you updated
Jono
-
You could probably just polish up those cam surfaces. Doubt you'd lose much from it!
Great to see some progress :bigok:
I bet you £20 it's standard bore 84.5 ;)
-
Flaming crankshaft pulley!!!! What a pain that was to remove without a holding tool.
So I'm getting there slowly with the tare down, hopefully if I get time I will have the head off by the end of the week.
Interestingly the company I am getting the internals from thinks I will need a re-bore an sleeve on the cylinders, can anyone shed any light on this, is this normally needed, can I not just replace the existing pistons without doing anything with the block?
Jono
-
Haha easiest way is with engine still in car, breaker bar leaning against the ground and crank it for a second.
Rebore and sleeve? I doubt it. More likely just need a hone unless it's out of round. Sleeves are cast iron. As long as you don't go too big no need to resleeve.
For my rebuild I just bought a hone tool for a drill and took off the glaze myself.
-
Ok, so guess what… the bore size is standard :D
I now have all of the new internals on order, that should take a few weeks before I get my hands on them, so I plan on stripping the rest of the engine and hopefully get it to the engineering workshop for some work.
I'm also thinking I might do the short shifter upgrade as everything is easy to get to, who has one? where did you get it from?
Also, I want to upgrade the breaks but the only kit I can find is too expensive really, its £1500 just for the fronts!
I noticed early on with the MX3 that it has the same caliper arrangement as an old ford escort, has anyone tried an escort break upgrade kit? If this works then its a very large cost difference.Cheers
Jono
-
Haven't heard about the escort swap, would be intrigued to hear.
What does work is the mazda BA 323f v6 2.0 spindles. I think you can even fit mazda MPS calipers onto them. Some guy on club-323f has done it.
Never bothered with short shifters personally so can't help there!
-
So things have been progressing well with the engine tear down.
The heads have been completely stripped down:
And are now in with my engineering shop for port & polishing and a general clean!
The block is now nearly completely stripped, the only thing that needs doing is to pull the crank out, that can wait until I need to as I'm running out of space for all the parts I have lying around lol
Bye bye old friends:
Nothing to see here, for now…
All going well the new parts should be here within 2-3 more weeks :)
Jono
-
Woohoo! Good work. How do the crank journals/rod bearings look?
-
Bearings actually look ok but I have new on order anyway :)
Getting close to re-assembly which is getting me excited lol
Still plenty of stuff to do, and a little research and more stuff to buy.
Jono
-
Just taken delivery of these bad boys:
Fun times ahead :)
Just need to find a big break upgrade option now!
Jono
