Sam's Proper MX-3 - LT Turbo project *Parting out*
-
Cheers Fella , still along way to go though :D
MOT next month Had to find a station with a flat drive on ramp as I wont get on normal ones now! Then im going to try and slot the rear hub holes for a bit of negative camber and tuck some tyre :bigok:
-
Did you sort your rpm gauge ? Thought It may be a mot issue ?
-
No still not done that yet! Have spotted a full set of 1600 clocks so I might go that route instead of having to resolder PCB's etc…
.. Not sure its a fail it does kinda move still just not very smoothly.
-
Amazing what I can do in the evenings now the clocks have gone forward plus working 7-4 most days now :D :D :D
Marco's Scarlet bumper now on 8)
-
Good work :) looks well. And x2 clocks in proper time again and sunny weather!
-
Cheers Bro tis funny that the work guys thinks it a different style bumper! looks more robust being all shiney and that.
Got out in the blaze again this afternoon to fit the new water bottle… If in doubt zip tie it out
Still a bit skethcy on the workings of the PS res bottle think that needs more work internally so wont fit that just yet.
-
Looking good man, hope you're going to tuck and smooth the bay when you're finished, will look a treat :)
-
Cheers mate yeah a T&S bay would be flippin sweet :D Lot of work though and I've got quite a bit to do already, so we shall see….
Did a small amount of tucking though by folding those white relays up behind the bodywork, plugs in the far corner by the brake servo got tucked back in and also lowered the brake servo hose down along with the wiring for the wiper motor out the way, so the whole rear edge of the engine bay is clear now and moved the earth to round by the headlight.
-
Have picked up an Intercooler I think will work and fit into the gap behind the bumper with both outlets out the same side ( they will need some slight modding though)
and this very special piece of pipework to connect it to the TB
-
If you want a small intercooler like that sam the audi a4 petrol turbo has one that slides in front of the wheel arch liner on the passenger side, it would probably do the same on the MX if you moved the washer tank
-
Nah the intercooler needs to sit in direct airflow so it will be positioned infront of the radiator behind the grill , tis the whole reason Im using that smaller width radiator so the boost pipes will go past it.
You can have a chargecooler in the engine bay as that works using water to cool the boosted charged air, but requires pumps/tanks and all sorts..
I will check out the Audi though thanks.
-
What a great start to the Easter bank holiday weekend! My car is now being featured in a JDM Euro stance blog :D :D :D
http://r32taka.com/2012/04/06/the-rare-mazda/#more-6862
..and to finish it off went straight through the MOT :cheers:
-
Did a bit more lowering yesterday! @ -125mm the bottom of the coilover body gets awfully close to the CV boot and I ground out getting out the drive!
It did look frickin amazing though…So jacked it up to -110mm in the front, ground off those two tow hooks underneath and cut back some of the plastic guards.
I Wont take anymore pictures of the whole car though till I get my new camera for my birthdays in a few weeks :P
-
Its not low enough…. lower it more! :bigok:
-
ha ha your probably right should of stuck at minus one twenty .still got a bit of wheel gap so I'm on the lookout for some sixteen's in the future to get my Fitment on point :-D
-
haha how do you get around that low?! I think I'm about half as low as you :lol:
Great to see some turbo components back in the log ;)
-
Had to change my driving style fo sure, by sticking to the speed limit :rofl: or sometimes under! When I first went to work in it on Monday I must of bumped the ground about 10 times, today about 3 times so you have to drive slightly towards the middle of the road to avoid the camber and potholes/deep drain hole covers or completely miss some roads out all together :D
Does feel quite gnarly though doing a big 'ol frame rail grind :bigok: Going to look see what damage if any I might of done to the sump at the weekend and try and formulate a plan to fit a guard in situ.
Yeah the kit is building up nicely 8)
-
Well no real updates of any work carried out, just some more picture whoring!
Didn't scrape once today and the sumps seems ok so I might take off another 10mm and see what happens :shock:
-
I love it! cant wait to see complete pics of it slammed
-
Cheers Josh shouldn't be too long now hoping for a sunny weekend on the 4th of May 8) Fitting a replacement wing tommorow with Archenemy booked up for Sunday to come and roll and flare again. Had to pay extra to get them down as the local guy was out the country till end of May and I wanted it sorted before Japfest on the 12th, so the fella is having a 250mile round trip just to roll one arch!
