Sam's Proper MX-3 - LT Turbo project *Parting out*
-
Congrats dude!! Nice and Easy MOT!! 8)
-
Thank Dude! More than pleased that I passed
with the small number plate letters and my rear
light mask too, covering up lots of the that indicator section :)Had to reverse onto there lowest set ramp at the tyre fitters :lol:
-
just a pre Japfest polished glamour shot :D
-
Seeeexxxxyyyyyy!!!!!!
-
looking really good buddy.. Can't wait to see it in the flesh tomorrow!! 8)
-
Really want to copy that gril if you don;t mind. As mines black i think i'd use red tubing round the hole. Is there any reason you didn't just connect the bottom grill to the top one to make it even bigger?
-
I dont mind mate :D the tubing is 5mm silicon vacuum hose
split up the side.
So like this?
bumper would be extremely flexible when cutting that out
(it could easily fold in half)
without some serious bracing involved, you would expose
alot more of the black bumper support and it would be even
harder to put some nice grill mesh in there…. but dont let
any of that stop you, if thats what you want it to look like :)
-
pretty sure its not worth that. Think yours looks better anyway.
-
ar thanks Jim, I didnt want say it was a bit ott
just in case….Thanks Marco for this pic :D
-
Alright folks, nice little development on the
turbo front here. Just spent 3 hours @ the breakers
Found an MX-3 removed the radiator, then spent
the next 2 hours 45 minutes looking at nearly every car radiator
in there! until I found this :D
Boost pipes will easily fit past the radiator now, making
the intercooler set up so much easier.other development taking place this weekend are coralating
my car ECU loom with the schematics I have from .com, to make sure
there the same so I can then send them off to Boomslang to make the harness.
1/3 of the way there to buying the SPEC stage 2 clutch I also require.Will do the rad first, then probaly the clutch(remove egr while im there), then get the AEM + boomslang up and running, once all those mods are proven good and working, I can start thinking about putting on the turbo, injectors and intercooler.
-
Excellent, looking forward to this build
-
Me too!
someone was aking for a shopping price list for this Turbo conversion
so here goes:323 Turbo manifold >10
323 Turbo baffled sump >5
IHI VJ-11 Turbo >90
AEM F/IC ECU >280
Boomslang harness >110
wideband lambda > 130
SPEC clutch >200 +100 delivery
Injectors > 20
Boost pipes/joiners/silicon elbows > 30 - 80
hose clips > 20
Intercooler > 10 - 100
Oil lines > 20
Water lines > 20
Boost guage > 30
Exhaust flexi > 20
sundries > 40Say about 1K is a good estimate there, not including a mapping session
as we are going for a street tune to begin with 8)
-
Ok after alot of studying and researching
diagrams yesterday, we are proposing to
make our own boomslang patch loom, saving
a good £££, it dosent look too difficult.wiring schematics from .com we are going to assume are
the same, will test all the ECU pinouts just to be sure though,
the 95-98 1.6 MX-5 ECU pinouts are the same, bar a few discrepencies!So if our loom is a succes, we maybe able to do others for the 1.6
AEM install.
-
Started making this today > its going to be a header
tank for the new rad. install.
-
Looking good,
maybe some nice polished battery cases are on the cards too if you get any spare time :wink:
-
cant do them, there not circular :lol:
The 'shop round the corner have alot of benders though :wink:
-
I knew that i didn't have the funds to do the 1.6 turbo but now i'm pretty damn sure i don't have the know-how to do this.
-
@816df7e8c0=youdirtyfox:
The 'shop round the corner have alot of benders though :wink:
Umm, hairdressers?
-
@6bc6cb934c=JIMBOfred:
I knew that i didn't have the funds to do the 1.6 turbo but now i'm pretty damn sure i don't have the know-how to do this.
You can learn the knowledge from here Bro :D
it is a case of quite a bit of research and reading
check the FAQ's from garrett I posted up also.This is my second Turbo conversion, so I've learnt alot from the first
but before that I hadnt really tinkered with cars that much.
-
I workied on heavies for a couple of years but was mainly servicing and so turbo's are a little still a bit alien to me.