Would these fit the MX3?
-
http://www.ebay.co.uk/itm/261157174356?ssPageName=STRK:MEWAX:IT&_trksid=p3984.m1423.l2649
Anyone know of any other\better ones?
-
Im sure they will fit but i have these
I have them on all four wheels for 3 years now with no issues. I just make sure they have lock tight on them and tighten them down every 6 months or so….
-
V nice if not a little pricey :shock: is that for a bag of ten? :rofl:
kulluminati777 does your insurance network 'frown' upon items such as these when modding your vehicles over there? Over here they'd see it as an excuse not to 'pay out' if the unfortunate happened and you hadn't informed them of their fitment? :x
Any noticeable kick in low speed steering? or 'bump steer' on uneven roads on front wheels?
Do you know the weights of said items?
kev b.
-
I paid about £100 for four from US, they had studs in them and bolted to the hub. Whats the centre bore of them spacers?
-
No idea, as much as I know, the wheel fitting is 4x100. That's my brain exhausted on the wheels side of things.. :?
My main issue is, with all the weight almost gone from the rear of the car, I thinking a wider stance would give it more traction when chucking it into a bend, or at least, give it some wiggle move when the sucker spins.
I've spun every MX3 I've owned, in the dry, rather not damage this one when it's working. :rimshot:
-
Think kulluminati777's are 54.1mm bore????? :?
-
@e07a89496f=youdirtyfox:
I paid about £100 for four from US, they had studs in them and bolted to the hub. Whats the centre bore of them spacers?
You got a link or a shop bud?
I can't fit my coilovers without a set, the mounting points on the bottom are just tapping the rims.
-
Check they is right thread pitch though.
-
http://www.ezaccessory.com/Thread_Size_and_Bolt_Pattern_Applicatoin_Guide_s/12.htm
Think we have a winner.
Thanks Dirty.
Motherofgod on the shipping for two sets of them :(
-
@1910788178=Lori:
http://www.ezaccessory.com/Thread_Size_and_Bolt_Pattern_Applicatoin_Guide_s/12.htm
Think we have a winner.
Thanks Dirty.
Motherofgod on the shipping for two sets of them :(
Thanks for sharing the link !
Also comes in handy when looking for other brake disks with similar bolt pattern.
-
Why not just do a 5 stud swap from a mazda 323?
http://www.uk-mx3.com//forum/viewtopic.php?t=5814&postdays=0&postorder=asc&start=45
That way you know its bullet proof.
-
It's a lot of cash for something that (from my understanding) won't help push the wheels out to fit the coilovers. Larger brakes are on the cards for the future, but not for a while.
-
Lori, what coilovers you got? I had issues with my k sports coilovers. My rear tyres were rubbing the springs on the back I got around it by fitting skinnier springs on the struts. Just wondering if you have the same problem?
-
I have zero clue bud, will PM you a few images.
It might be just because the car is in the air right now, so the wheels are bowed in toward the frame, but I can't see how that would impact anything as the distance between the bottom of the strut and the inner rim wall is static.
-
I see what your trying to do now.
You could use wheels with a different Offset.
Or
You can get spacers if its only a few mm you need to move. You can get bigger ones like this but they are no good for the MX-3 as it uses nuts not bolts.
Or
You can get big spacers that work the same as the stud conversion ones you linked to, but they don't change the stud pattern.
AND
If you move them out too much you might need to stretch the tyres to get them to fit without rubbing OR roll the arches OR both.
-
I'll go for the bigger ones, I've got 4 sets of rims, each one with new rubber so I'd rather not have to buy new ones lol
Thanks Admin, Appreciated
-
The 'Pictured shims' can be used on mexy's if its only 'mm' your'e trying to gain, by drilling two small holes in the shim, countersinking them and then centralising the shim on the inner mounting face of the wheel and drilling tapping into wheel using 4mm screws.
It obv depends on your wheel structure but carefull assesment of each screws location would allow the shims to mounted to wheels permanently assisting when fitting/removing wheels :)I have done this on several modified project vehicles where small clearances for 'ball joint boots' and suspension components are all that is required
The centralising of shim is only mm crititical an can be done by 'eye' if required but as always…...... "measure twice, cut/drill once!!!"
kev b.
Oh! PS always wise to re balance wheels anyway after any mods at any corner, especially fronts :)
-
Lori your a bit 'RIM GREEDY' arnt ya???? :rofl:
Is it a set for SPRING, SUMMER, AUTUMN, WINTER?? :shock:
greedy boy! :mrgreen:
-
2 Sets with the Equipe.
1 From my old MX3 - Used as step-ups or paint backdrops.
1 From the AZ3.Going to need a garage just for rims shortly.
