Project: Gray Death.



  • Thanks Kev,

    This was my third MX3.. Won't be getting another now, time to move on.



  • If my car was on the road I would come up and sort it out, I will get to the garage tomorrow and look at your issues and photo them

    You are 99% there so why give up now

    A lot of your advice has been from USA and the LHD versions hav different piping system due to the brake servo being on the other side



  • Is it just vaccum & electrical connection issues that are stopping it from completion or do you have other items to finish ?.
    Is the dash swap all done and ready?.
    As dj said I would drive up but my tax has expired and I'm working 7 days a week until December now :(
    Plus your bloody miles away lol!.
    I only get 500 miles a year on the insurance :(



  • Sorry for the tantrum guys… this thing just pisses me off at times.

    @f877c89227=Garfy1981:

    Is it just vaccum & electrical connection issues that are stopping it from completion or do you have other items to finish ?.

    Mainly.

    A few other small things,

    1 - Work out the wiring setup for the 4 pin 02 sensors.
    2 - Refit exhaust. (need to chop some off)
    3 - Weld the drivers side sill
    4 - Fit the Airbag Steering wheel
    5 - Add coolant.
    6 - Look at the drivers side drive shaft, Can't find anything to lock it in with, so it's just pushed in…

    @f877c89227=Garfy1981:

    Is the dash swap all done and ready?.

    Dash is 99% done.

    Rewire the hazard light switch. (currently disabled)
    Swap the HAVC panel for one with AC button. (Yes mine has it)

    That's it. The first and only (that we know of) UK shell with the import dash style.

    Fooking proud of that tbh.

    Other then that, it's in the shop for some exhaust goodness and a terraclean.

    Look gents, I appreciate the offers driving up here to help and yeah, you could help but if I'd feel way to bad for anyone to do that, so please don't.

    Skype video calls are just as good if ya use the service and ya willing.



  • Just a suggestion lori, if you are doing exhaust by a stainless kit and do the modding to the center pipe, much easier and a massive difference in power.
    If you are welding sills then do the center pipe at the same time ( mig welders will weld stainless pipes together )

    The drive shaft should have a little circlip that goes n the groove on the end, I had a missin one and went to vauxhall and got a vectra one in mine as thy cost a few pence each and were on the shelf

    O2 sensors I think only have 3 wires into a 4 pin block white black & blue

    and for being pissed off, try rebuilding an engine fitting it and finding the £3 oil seal behind the flywheel leaks, thats annoying and just another thing to deal with in modifying. If it was easy putting an mx6 engine into an mx3, halfords would sell the kits for £5000, its not modifying of sorts just time eating and dealing with every issue you can think of if that the haynes manual doesnt cover lol



  • @0786dea913=djmarcopolo:

    Just a suggestion lori, if you are doing exhaust by a stainless kit and do the modding to the center pipe, much easier and a massive difference in power.
    If you are welding sills then do the center pipe at the same time ( mig welders will weld stainless pipes together )

    The drive shaft should have a little circlip that goes n the groove on the end, I had a missin one and went to vauxhall and got a vectra one in mine as thy cost a few pence each and were on the shelf

    O2 sensors I think only have 3 wires into a 4 pin block white black & blue

    and for being pissed off, try rebuilding an engine fitting it and finding the £3 oil seal behind the flywheel leaks, thats annoying and just another thing to deal with in modifying. If it was easy putting an mx6 engine into an mx3, halfords would sell the kits for £5000, its not modifying of sorts just time eating and dealing with every issue you can think of if that the haynes manual doesnt cover lol

    Got the ebay set :) I'm using a cat-less center pipe so need the cat adding in.

    My 02's are 4 wire, 2 white, 2 black.
    Will take a look at the drive shaft, couldn't feel anything on the end to hold it in thou.

    Yeah, that would frack me off, this whole thing has been fun but I gotta be honest, I won't be doing it again. You got more desire then me to do that bud. Respect.



  • Stick at it Lori, because if you do and when you finish it, when you drive it you'll be glad you did! :lol:



  • @4fd39e8e45=mx3gulf:

    Stick at it Lori, because if you do and when you finish it, when you drive it you'll be glad you did! :lol:

    This!



  • Picked up a mint Mazdaspeed spoiler with baseplate this morning.

    And the delivery of 2xslim line fans, an oil catch can should be going in tomorrow.



  • Good to hear you are back at it Lori!



  • It might piss me off from time to time bud, but hell.. I want this fucker finished.

    PM me your address bud.



  • Maybe just get it driveable & legal at first, as there is no such thing as finished in the car modding world :lol: :P



  • It will be drivable before Christmas, won't be legal (nor see a road I should add) till afterwards.
    Most of the parts (except the MS spoiler) are replacement parts for ones that are broken or easier to fit with it in it's current state.

    The MS spoiler was £50.. couldn't pass that up.



  • Sounds positive Bro. Nice score on that MS piece too!



  • 50 quid? Mother of God, some bargain!



  • @5b7b226916=jayom:

    50 quid? Mother of God, some bargain!

    Hell yeah.

    That means that in my garden, I now have every official spoiler they ever made for the MX.

    Wraparound.
    RS (slightly raised)
    Stock UK one (Not raised)
    Mazdaspeed.

    Thou, not sure why… meh.. lol



  • Well, with DJ's help on Skype video! the bay is 99% done and ready.

    Left to do:

    1 - Remove the EGR from the block and bolt the blanking plate on. - DONE
    2 - Extend the EGR loom to the EGR on the back of the inlet and plug in. - TODO
    3 - Swap the rad fans to the new slim line ones and add coolant. - DONE
    4 - Bolt exhaust on and clamp end can on. - DONE
    5 - Route the oil catch can into the air intake pipe. - 50% DONE

    Smaller jobs:

    1 - Remove the center console and attach the short shifter on (right this time) - TODO
    2 - Swap the HAVC controls over to the AC ones. - JOB SCRAPPED

    Would have got to a point I could turn her over today but rain ended play…. Bloody British weather.

    DJ = Fooking legend!



  • Great news Lori, light at the end of the tunnel!



  • Legend! Sounds as if it's all gone well and ready to fire up soon!



  • & here she blows.

    http://youtu.be/X9jS4_YuLP4

    :D :D :D :D :D :D :D :D :D :D :D :D :D :D :D :D :D :D :D :D :D :D :D :D :D :D

    The 02 Sensors aren't wired in yet, nor was the rad fans.

    The smoke at the back was the EGR out on the rear down pipes not blanked off yet..


 

Copyright 2021 UK-MX3.com | Powered by NodeBB