Welly's - GT4 Engine Swap Project (Celica GT4 / MR2 REV3)
-
Porting & Polishing
GT4 dash brackets, which we made.
-
what plans do you have for the out side :?:
-
None.
its a street sleeper.
rarther chuck 2k at the engine rarther that the styling.
it could be getting resprayed in Arden Blue though.
-
looking sweet as. cant wait to see it up and runing. following that. would have to some slight alteration to body. nothing too fancy. just something to say its standard looking but not standard. etc mind game.
-
engines nearly rebuilt.
forked around 500 out for engines parts :)
she should be running a very healthy 375bhp+
-
Got a few pics, but this ones the block and gearbox and theres about 1/3 of a inch gap between, chassic and engine and gear box.
-
@501bd0e5bc=Welly:
wait till the air vents are going through to the breaks ;)
have you made these ducts yet? if so any pics?
I was considering doing this on mine since I have not installed my foglights yet and it seemed like a cool idea… either that or running my CAI down into a foglight hole :shock:
-
this is looking sweet! Can't wait to see some vids of it in action!
-
ok, engines in and it runs and it DID move, the clutch has gone bang :lol:
put ill post some pics, also engine now stands us at a further 1k.
exhaust is full stainless with a HKS trust back box.
inside the back box.
-
not much room in that engine bay lol
-
you should of known this when we started had to make a custom air intake.. as it would'nt fit.
Rad aint fitted yet either.
-
What size exit is that?
Jono
-
4 or 5 inch.
full stainless back box is hks.
cost of exhaust system £0.00 :wink:
-
found out problem with clutch..theres a plate that we needed to buy after further research.. transfer plate got 1 for £50..
it ripped centre of clutch out…
Kami was saying on msn UPGRADE!!! UPGRADE !!! lol
-
awesome car dude, you need to post more pics tho, can't wait…
-
just to show u what the gt4 can do. http://youtube.com/watch?v=8hvv5qGRbEA&mode=related&search=
took ours out for a slow run hit 5k and jesus fucking christ pinned me in seat.
vids will be done when engines run in.
-
ok, been working on it again 2day..
alot faster now timing is getting there..
gna plug it into krypton tuning some time.
it breaks traction in a few gears and we was only reving it to 4500.
traction is fairly good though, it pops and bangs lol…
got a video of first tester run, at 4500k revs.
http://s202.photobucket.com/albums/aa217/WellyMX3/
got a few things left to do, then dumpvalve etc will come.
-
http://youtube.com/watch?v=8T7EZyT2n00
engine has a few faults, engine managment light which is cutting boost and power :(
most of engine sensors arnt working either.
we'll sort it.
-
v nice project mate .
but with your base car being a stock 1.6 automatic , you will have to change a hell of a lot of parts ! or she will go boom
-
gear linkages toyota,drive shafts toyota,engine toyota with AM internals,
she aint going to go boom mate.
in the video was only bossting about 4psi because of ecu and sensors..just wait till we boosting the standard 16.7 should shift then abit more for scooby teasing lol
front suspension legs changed for V6 ones as a a little bit stiffer.
engine mounts all made perfect etc.
