Changing Spark Plugs
-
have you noticed anything unusual ?? if not then id probs say youll be fine…. altho never say never
-
no, the cars running amazing, as always…
-
I need to change these plugs today or tomorrow, before I take the car in for an MOT.
I have emptied some of the oil, so its below the Full marker, but there is still oil in some of the spark plug chambers.
Is there an easy way to get this oil out? I don't want to take out the plugs until I've got rid of the oil incase it gets any further into the engine!
-
look at girl racers post saying help! i have given her info on how to sort it out! if there is a good bit of oil and you have the balls suck it out with a straw… but for the love of god dont get it in your mouth!
u should be able to burn off a few cc of oil if it falls into the combustion chambers but i say SHOULD!
-
@d5388ad20f=irish-mx3:
look at girl racers post saying help! i have given her info on how to sort it out! if there is a good bit of oil and you have the balls suck it out with a straw… but for the love of god dont get it in your mouth!
u should be able to burn off a few cc of oil if it falls into the combustion chambers but i say SHOULD!
- aye, take them notes in hand. Very helpful indeed.
Urgggg, couldnt use a straw !!
-
if needs be done!
-
You could use some compressed air to blow it out if its just small bits you cant get to, just put some tissue over the top so it wont blow everywhere.
-
get a paint tinting syringe and use that to suck it out
-
I already made a little device with 2 straws, a plastic cup and some parcel tape, worked really well actually and it stopped any oil from getting near my mouth. Will get the remains out tomorrow with a rag and get those new sparkys in. Its gonna be v. awkward getting the back ones out, those holes are so damn deep!
-
long extension bar, i though i would have that problem but very easy in the end
-
The mx3s are know for having bad Valve cover gaskets, in fact they are crap.
If you pull your plugs out and they are drwoned in oil, (Usually the rear ones) please dont panick. We all have this problem specially if you are prone to flooring the car. you have two choices: taking the valve covers off and replacing the gaskets for new ones, or you can re use the old ones and use locktite liquid gasket to seal the gasket around the spark plug holes.We have replace valve cover gaskets for new ones only to find out that within 2 months they are leaking again. So now we always use the liquid gasket just to reinforce the spark plug holes, this is the weakest point.
If you are driving around and you start to smell burning oil, this is probably the most common cause, you're rear valve cover gasket will leak from the backside and the drops of oil will run directly onto the rear exhaust manifold, so again dont panick, its not the block.
Over filling the block with oil is Bad….really bad as the other meassages explain....always fill on a level surface and always check the level when the block is cold, like first thing in the morning.
-
They are also known for having spark plugs that are a bitch to get out!
Been tryin for the last hour and I've got 4 out, but then realised I can't even reach the middle back one with the tool I'm using! Grrrr…
I just tried to order a foot long one and my cards been declined, so I'm gonna have to ring round a few friends and hope someones got one!
-
yep, you will need a good socket set and two extensions, otherwise as you know you will not reach.
-
Is it bad for the engine to drive the car with 4 new iridium plugs and 2 old plugs?
-
Its not bad, but its not good either. If you have to drive to get to somewhere, where you can change the plugs, dont go above 400rpms. As long as all the plugs are from the same heat range you cant do any damage, but still irridiums have a much stronger spark than your old plugs, giving you an unbalanced combustion. try to get them chamged as soon as possible. Try going down to your local garage and explain the situation, do a bit bowing and a bit of groveling and they might lend you the correct tool :-)
-
I'm not gonna risk it, but its so annoying not being able to drive the car, especially after I've just got the new exhaust fitted! :x
-
i bought halford socket set think was 14 quid. included extension bar spark plug socket and angle attachment. all of these were all i need
-
I have one of these:
http://img.alibaba.com/photo/50935051/Spark_Plug_Sleeves.jpgand its only a few cm short :cry:
-
think the problem the may be the angle adaption is on the bottom. also the bend could damage the port for the plug
-
nah, its been ok for 5 of the plugs, but its just a little too short for the middle back one. If only i had my toolkit here i could prob bodge something up, but i left it back at uni :(
