New Backbox soon to be required…
-
Heya, I have the 3" sportex tail pipe and its just perfect, not too loud and you get a nice over run when you lift your foot off the accelerator, when the car is really hot on the motorway for 20 mins or more then the exhaust really pops when you change gear.
I have a sportex 3" tail + a standard mid section and it sounds nice
I think the 4" might be a bit too much but I may be wrong
-
**Incidentally, when Red started blowing I trucked up to Powerflow with "Standard look, standard sound" as the remit. £300 from the cat back.
However, they couldn't quite manage the sound, despite filling the backbox full of baffles to quiet it down and three years later I still don't care 'cos it sounds lovely :D
They didn't quite manage the look either - they saw two, 2" pipes and gave me two, 2" pipes. They didn't notice that the 2" wide bits were actually resonators and the pipes themselves are only 1" exit. I still don't care though :lol: They look great - close to stock and not OTT.
For £300, it was worth it.**
-
@9ff0a6e794=Rainmaker:
That one gets my vote, looks very nice!
-
Its a shame they dont do a 3'' slash cut as the wife love the 4''slash cut not a 3'' round.. yeah i know i have to ask for her in put as Wes is her baby…
-
On my first MX I had a universal 4.5" slash cut straight through backbox, made by a company called Megansport, and damn did it sound good. Way to loud really, but I was young and childish back then :p
The only thing I have to say is that using a backbox like that may have sounded awesome but it sort of lost that distinct v6 noise a bit :(
-
Ive been on youtube alot lately and listening to exhaust sounds from mx3's and i see quite a few had 4''round or slashcut, i know mine is only a k8 but i wont be removing the cat or having a straight through either so maybe a 4''slashcut will be a nice note to listen to for the v6…
ps.. i have ordered a backbox now but youll have to wait till japfest to find out...lol
-
ooh you tease :p
-
im guessing two bakedbean tins :lol:
-
Never say never…
-
:shock: looks good :lol:
-
thought id get it nickel plated for show too…lol
-
well that's just awesome! I think I need one of those lol xD
-
@2dcc3011a2=Rainmaker:
Its a shame they dont do a 3'' slash cut as the wife love the 4''slash cut not a 3'' round.. yeah i know i have to ask for her in put as Wes is her baby…
meet Her half way…
I reckon I'll go for something like that, and burn the end at work on the oxy,lol
-
before
after
if that helps at all!, 3inch rolled.
-
that does look good
-
@0a0147ee51=Garfy1981:
That does look nice! I like the red indicators as well :)
-
4 inch straight cut. ( could be 4 1/2 ? )
I had my exhaust tip re done as felt it stuck out too much, it now sits tight to the bumper.
well hope that helps i dont have any pics of slash cut mx-3s to show you unfortunately.
-
That looks a bit badly mounted as it looks like its touching the bumper
Does it rattle a lot???
On mine I have a good 2" gap between the bumper and the tail pipe
-
Yeah I didn't like it hanging down and sticking out like a saw thumb. Bumper has been trimed slightly where it would have burnt it. It's a mandrel bent system to 2.5 inches. It's proper solid does not move or bang. But then the whole system cost 1k so it should be perfect!
-
This is what I've got sitting around waiting to put on mine….
5" outwardly rolled Rage ST150