Sam's Proper MX-3 - LT Turbo project *Parting out*
-
Looking good,
maybe some nice polished battery cases are on the cards too if you get any spare time :wink:
-
cant do them, there not circular :lol:
The 'shop round the corner have alot of benders though :wink:
-
I knew that i didn't have the funds to do the 1.6 turbo but now i'm pretty damn sure i don't have the know-how to do this.
-
@816df7e8c0=youdirtyfox:
The 'shop round the corner have alot of benders though :wink:
Umm, hairdressers?
-
@6bc6cb934c=JIMBOfred:
I knew that i didn't have the funds to do the 1.6 turbo but now i'm pretty damn sure i don't have the know-how to do this.
You can learn the knowledge from here Bro :D
it is a case of quite a bit of research and reading
check the FAQ's from garrett I posted up also.This is my second Turbo conversion, so I've learnt alot from the first
but before that I hadnt really tinkered with cars that much.
-
I workied on heavies for a couple of years but was mainly servicing and so turbo's are a little still a bit alien to me.
-
you'll be fine then, its just understanding the concept
of 'forced induction' next.
@3846eb1d4e:
A turbocharger is used to force air/fuel mixture into an engine at a pressure greater then the natural atmospheric pressure of around 14.5 PSI. When a turbo produces 7 PSI of boost, this means how much extra pressure it applies on top of the natural atmospheric pressure. The way a turbo works is the exhaust coming out of the engine is pushed through a turbine. This turbine is mounted on a shaft, which in turn spins an air compressor. The compressor draws air in and blows it into the inlet manifold, and this produces BOOST. The whole point of forcing the air/fuel mixture into an engine is to allow it to burn more fuel and make more power with the same engine capacity. This can get complicated, as there are several factors that get in the way of efficency gain. For one thing when you compress air (with a turbo) it gets hotter. The problem with hotter air is that it contains less oxygen than cooler air, so there is less oxygen to help burn extra fuel that’s going into the engine. This is why many turbocharged cars use “intercooling” of various types, to cool the pressurised air back down into the engine.
-
@3fdcd893f8:
It’s important to consider problem of too much heat inside the engine. Once the hot compressed air goes inside the engine it is then compressed again by the piston in the engine. Therefore by the time the mixture of fuel/air mixture is ignited it is really hot. When it is too hot it could ignite itself before the spark plugs fires (known as pinging). When the engine pings the smooth, well-timed normal ignition mishaps, costing you power and damaging ports to the engine. Damage is caused to the engine, and can therefore lead to blowing the head gasket, this then chain-reacts to more severe cases. Another problem when the engine has an air/fuel mixture which is too lean, that is not enough fuel for the air coming in, which creates too much heat, or having ignition which is not suited to the engine. With private turbo installations these problems are often ignored. The ignition timing required for optimum power and smoothness from a turbocharged engine is in fact totally different to that required for a non-turbo engine. This is because the more efficient the engine is, the less advanced the ignition timing needs to be to get power combustion of the fuel/air mixture. When the engine gets more and more boost, the ignition should happen later and later in each cylinders or rotors combustion cycle. To get best out of the turbocharged engine it needs a balance of boost, mixture richness, charge air temp and ignition timing that allows it to run smoothly and efficiently with the type of fuel you're using. If you use low-octane fuel, it is more susceptible to pinging as it ignites more suddenly and erratically. The higher the octane of your fuel, the more smoothly and progressively it will burn, which helps prevent pinging. This means that with better fuel you can run more boost or more advanced ignition without any engine difficulties, which indeed means more POWER.
So the piggy back ECU ( meaning its run in harmony with the stock ECU)
supplys more fuel by holding the injectors open for longer (along with larger injectors) and re-tards the ignitionwhen on boost. The Turbo shaft is lubricated with oil and cooled with water,
so you need to supply it with both, high pressure oil line can come from
the oil pressure switch, or in the case of the B6 engine it already has a tapped hole in the side of the head to use and it drains back into the sump after the turbo, the water connections can come from the top radiator hose and drain back
into the bottom radiator hose. Intercooler for cooling the charge down, and uprated clucth to handle more torque that the engine produces. The wideband lambda sensor is to keep an eye on the Air/Fuel ratio, and the boost guage keeps an eye on the boost pressure being generated.Hope this helps :)
-
Did a bit more today on the header tank,
waiting on the filler neck & rad cap to arrive, bit
more welding and polishing and she'll
be good to go :D
-
Factory shutdown! so Im on Holiday now!! :D 8)
Cant finish the tank now though :(
Needed to do a bit of sussing out anyways…
thinking clear filler hose or see through green hose
would look quite mental.
Slim line 12" rad fan on order, to make even more room,lol
Been checking how straight I can get this boost piping, less
bends the better as they generate more heat…
be back soon with full rad install :)
-
Drooling dude, sooo shiny 8) 8)
-
CHeers Bro, she's still the garnet paper & autosol treatment
to go, so it will get more shiny bling bling. 8)
-
Welcomed in a new addition today
Mr Sharp shooter is along for the ride!
-
:lol: :lol: :lol: :lol:
-
Rear wiper deleted now also.
-
nice what did you bung the whole with as im thinking of doing the same on wes
-
I kept the original rubber washer in there and shoved
in a little barbed end cap like the ones you get off tubular
flatpack computer desk's etc.Tbh I need to find something better as it looks a bit button
like from some angles, once I found a better grommet will
let you know.
-
Glue a red golf ball on it :roll:
-
is that a new Japenese car fashion gimmick that Im unaware off…
...or is it a gag ball reference? :lol:Could use the hole for the aerial for when I remove the roof one :wink:
-
behold, more shinyness! radiator cap from a Capri :shock: :D
back to work tommorow so I can get this all welded up
few more bespoke bits to make, then I can hopefully
fit this up next weekend :D